Batteries, which are now incorporated into mobile devices, are small wonders of technology. You save more energy than before and can be recharged any time. With the right tips and tricks can the battery power maximum fullest. We have compiled for you ten tips to help you achieve optimal battery performance:
For fast charging of your mobile devices you should therefore always the original charger or use of third-party that was developed precisely for your device.
Many laptops offer a combination of standard USB port and charging USB port. However, these are usually in insufficient. Then only helps trying each port or a look at the manual. Some devices also support only up to 1100mA. Although the new USB 3.0 port delivers up to 900mA current event, this also supports only USB 3.0 devices. Closes her so at an older phone or an adapter with USB 2.0 function, 500mA only be issued maximum. And a caution: When using some USB hubs, the current is also distributed to all ports. Then it is even less power.
A used battery should never be thrown in the trash because it contains toxic chemicals and is also flammable. Therefore discarded best are no longer used batteries in boxes in hardware stores or supermarkets.
In the window "Properties of Generic USB Hub" then click on the "Power" tab. Here you can see a list of connected USB devices, along with the amount of energy that pulls the device. This information can help you determine if the device is quickly charged (500mA) or relatively slow
1 Fast battery charge thanks to the original charger
IPads and other tablets have larger batteries than, for example mobile phones. The original charger of an iPad here offers a capacity of 2100mA, or about twice the current that supports a typical USB port. This additional power is also noticeable. So the iPad is charged with the original charger in about 5 hours while it lasts, for example, with an iPhone 5 charger good for 10 hours. This loads only at about 1000mA. If you insert a USB travel charger from a third party, it can take up to 24 hours for the iPad is fully charged. Some chargers also include circuits that prevent a full power. For example, slows an original Samsung charger for charging an iPad. It's just the reverse.For fast charging of your mobile devices you should therefore always the original charger or use of third-party that was developed precisely for your device.
2 Many phones do not need to specific chargers
However, most mobile phones do not need special chargers. The small batteries are fully charged about the same speed with other devices. So an iPhone 5 is charged with the original charger in about 2 hours. With an HTC Travel Charger in 2 hours and 4 minutes, and with a Samsung charger in about 3 hours.3 Charging with the USB port
All mobile devices can be recharged with the correct adapter via USB. USB 2.0 ports are available in two types: standard and charging cable (Generic). A standard USB port only provides 100mA poor, while a special USB charging port provides at least 500 MA. Larger devices such as tablets, however, usually not or only slowly charged via USB.Many laptops offer a combination of standard USB port and charging USB port. However, these are usually in insufficient. Then only helps trying each port or a look at the manual. Some devices also support only up to 1100mA. Although the new USB 3.0 port delivers up to 900mA current event, this also supports only USB 3.0 devices. Closes her so at an older phone or an adapter with USB 2.0 function, 500mA only be issued maximum. And a caution: When using some USB hubs, the current is also distributed to all ports. Then it is even less power.
4 . Charging via Micro-USB
For devices that have Micro USB connections, you can all cables that have a Micro-USB plug for charging, use. You do not need a special Micro USB cable.5 Important: The first charge
The first charge cycle is vital in any battery: Here, the state of the battery is determined. If you afloat the device for the first time, let's invite her this for at least 12 hours, it takes off and then used the device until the battery runs out of juice completely.6 Long battery charging allows
Batteries contain circuits that control the flow of energy. This allows a continuous charging. When the battery is fully charged, pays a battery management controller that the battery is not overcharged. Lithium-ion batteries could explode namely.7 increase. Lifetime through complete discharge
Modern lithium-ion batteries have no memory effect problem, so they can easily be charged even if the battery is not yet completely empty. However, many manufacturers recommend fully discharging the battery of the device at least once a month and then fully recharge. This prolongs the life cycle of your battery.8 treats. Well battery and let the device
Treat your battery well, he will prove you good service for many years. Transported the battery, therefore always best in the device and ensures that the battery would collect no external impacts. Inside the battery is after all chemicals that should be protected.9.Replace batteries
However, no matter how well you treated, it's battery, sometimes causes loading capacity after. The battery life is shorter automatic. Use of chemical changes inside the battery. So Apple indicates, for example, that there is still about 80 percent battery power available after 1000 charge cycles. Other manufacturers refer to similar values.A used battery should never be thrown in the trash because it contains toxic chemicals and is also flammable. Therefore discarded best are no longer used batteries in boxes in hardware stores or supermarkets.
10 diagnosis of a USB problem
Problems of charge via the USB port can be studied also in Windows. Clicking this in the "Control Panel" under "System" to "Device Manager" and select the "USB Controller". Every single USB port (Generic USB Hub) can now examine the "Properties" by clicking the right mouse button.In the window "Properties of Generic USB Hub" then click on the "Power" tab. Here you can see a list of connected USB devices, along with the amount of energy that pulls the device. This information can help you determine if the device is quickly charged (500mA) or relatively slow